Parts & Accessories
$4.00 - $6.00
Used to adjust crank chainline or ensure proper bearing preload when using 30mm spindle cranks. - Inner Diameter: 30mm - Outer Diameter: 41.5mm - Machined engineering-grade Delrin - Sold Individually
Race Face CINCH Crank Puller • Puller cap for Cinch model Race Face cranks only, including Next SL, SixC and Turbine • Puller cap utilizes 16mm hex key • 26mm thread
- Pedal Spindle: 9/16" - BB Included: No - Chainring BCD: 96 Shimano Asymmetric - Intended Use: Mountain - Spindle Interface Type: Shimano Hollowtech II - Chainline/Hub Compatibility: 141/148 Boost Hubs
This very light, stiff, and strong carbon crank spider optimizes your power transfer. - Stiff and lightweight. - For use with S-Works carbon road cranks.
Replacement spindle spacers for Race Face X-Type XC/AM cranksets.
- For use with the P38s chainguide or as a stand-alone bashguard - Machined backside for optimal strength and weight, smooth outer surface eases cleaning - Aluminum inserts at chainring bolt holes prevent damage during installation - 36t to 38t capacity
Race Face aluminum chainring bolts for inner chainrings. Includes four 12.5mm bolts.
Race Face direct-mount chainring spider for Cinch ranksets.
The Stages Power meter is built on to a non-drive FC-9000 crank arm specifically to pair with Shimano's Dura-Ace 9000 crank. This meter has been proven, as it was ridden to victory in the 2015 Tour de France by Team Sky. This Stages Power meter is slimmer, and up to 28% lower profile than our original meter. It's sleeker by way of a 17% reduction in frontal area, and Stages also made it stronger. The new housing design increases the strength of the battery door and housing connection by 200% over the previous design. This Shimano Dura-Ace 9000 Stages Power meter is compatible with all Shimano Hollowtech II road drivetrains. - Accuracy: ± 2% - Power meter housing: new low profile design, with new door interface - Weight: Only adds 20g to base crank arm - Battery Life: 200+ hours (coin cell: CR2032) - Power range (Watts): 0 to 2500 - Cadence range (rpm): 20-220 - Water resistance rating: IPX7 - Frame Compatibility: Most frames, see fit guide in our Support section - Device Compatibility: ANT+, Bluetooth Smart Ready Software Compatibility: Training Peaks, Strava, Garmin Training Center and others
SRAM’s cranks are strong and tough, ready for any kind of ride. So it’s inevitable that pedal strikes and debris will chip away at the end of the crank. SRAM’s Carbon Crank Boot is an upgrade that combats the wear and tear that comes with hard riding. The boot protects the crank from surface damage and keeps the rider’s style perfectly intact.
The North Shore Billet 2×10 Spider replaces the stock chainring spider so that you can run smaller chainrings on SRAM XX1, X01, X1, X0, X9, X7, and GX cranks using GXP bottom brackets. With the NSB 2×10 Spider you can run a more traditional 22/32T or 24/34T combination. The NSB 2×10 Spider is designed to use any standard 64 / 104 BCD 9 speed chainring. The distance between the rings and the distance from the centre of the bottom bracket is the same as the 120 BCD spider so the set up is simple and the shifting is quick!
Race Face crank bolt/puller for 2008 and newer Next SL cranks and 2012 and newer Atlas cranks.
Trail riding can be tough on your gear. The ends of your alloy cranks can take a lot of abuse as the trail rushes underneath you and your bike. Protect your cranks from any damage with Race Face crank boots - now made in a smaller version to fit most alloy MTB cranks. Made from a durable Race Face proprietary plastic blend, leave no doubt and go with the originator in crank end protection. Wrap it up and protect the tips. Compatible with: - Race Face - Turbine Cinch - Atlas Cinch - Atlas (24mm Spindle) - Turbine (24mm Spindle) - Aeffect Cinch (175mm length ONLY) - Most other popular alloy MTB cranks (except some alloy DH cranksets)
$90.00 - $117.00
Shimano Chainring Bolts - For use with M9000 chainrings
The 1x guide is the definitive cross-country chainguide. Used on the World Cup circuit and even in the 2012 London Olympics, the 1x has a proven track record of dependability and performance. The 1x is the perfect guide for riders and racers wanting a lightweight single-ring front drivetrain for cross-country use or riders wishing for more security out of their "narrow/wide" or XX1/X01 setups. Freshly updated for 2015 with the new co-molded "TR" upper guide - lighter and quieter, what's not to love? - Adds security to "narrow/wide" 1x10/11 and XX1/X01 drivetrains - Most models accommodate 26-38t chainrings - Tracked and grooved upper guide / backplate interface increases stiffness and eases installation - New co-molded "TR" upper guide with softer durometer interior for silent guidance - All install and adjustment operations possible with just a single 4mm HEX wrench. - BB mounted guides are only compatible with traditional, threaded BB systems
Utilizing MRP's patented integrated skid (US Patents RE 42,436 / 8,235,849 Patents Pending), the XCg tucks neatly behind your crankset and protects those costly chainrings from damage. The replaceable nylon skid glides over rocks and obstacles. - Great accessory to protect costly chainrings - Integrated skid protects chainrings and glides over rocks and obstacles - 88g (XCg V2 32t, ISCG-05 model)
The new G4 picks up where the famous G3 left off — three consecutive appearances in the Dirt 100 issue, as well as countless World Cup and FMB podiums made it the most sought after full-featured guide on the market. Upgrades to the G4 include a new co-molded upper guide that utilizes a softer durometer TPU material on the interior walls and ceiling to silence drivetrain chatter. An improved material formula is utilized in the updated skid — making the best even better. - NEW Full-size, nylon upper guide with co-molded TPU material on the interior walls and ceiling that silences chain contact. - Integrated skid protects chainrings and glides over rocks and obstacles. - Includes standard pulley and G-slide slider block for quiet, dependable operation in muddy and dank conditions. - Available in "Mini" 32-36t and "Mega" 36-40t sizing - Compatible with chainlines 50mm and wider (55mm and wider on 83mm BB shells)
All-City's lightweight Cross Wizard chainring guard is the perfect addition to a single ring or singlespeed setup. While not a full-on mountain bike ‘bash guard’ these are just the thing to keep your chain on and your teeth intact. Named after the one and only Cross Wizard! (You have to say it like that, with the exclamation at the end.) These are available in 110mm and 130mm bolt circle diameters for all your ‘crossy needs. - Material: CNC machined 6061-T6 aluminum
- Stainless steel chiainring/spider lockring for all e*thirteen cranks that use the Quick Connect Direct Mount System - Requires e*thirteen spider lockring tool. Use QBP part # TL0212
The North Shore Billet 1×11 Spider replaces the removable chain ring spider so that you can run a SRAM XX1 chain ring on Truvativ X0, X01, X1, X9, GX, S2210, and S1400 cranks. There are no mounting holes for the granny ring and the single ring’s position is designed to give a better chain line throughout the entire gear range. The chain ring tabs accept an optional rock ring for All Mountain or Enduro riding.
- Crank Construction : HOLLOWTECH II - Optimum power transfer
$46.00 - $49.00
TruVativ's Stylo All Mountain Guard is all-mountain chainring protection with style. This 4mm thick aluminum guide is 4 bolt, 104 BCD compatible.
Race Face aluminum Torx chainring nut/bolt set for triple chainrings. Includes four nut/bolt sets.
With the SXg, MRP delivers a guide without compromise and with no equal. No longer does the desire for protection and both upper and lower retention have to come at the expense of weight, efficiency, or the addition of moving parts - have your cake and eat it too. With the SXg covering all those bases, it’s the first guide in history that’s equally at home on anything from aggressive, short-travel bikes to Armageddon-ready Rampage rigs, and everywhere in-between. It’s a guide that refuses to be pigeon-holed, blurring the lines between typical industry definitions - a little country and a little rock, as they say. But, in this case, it’s a whole lotta rock. High-security chain retention and bulletproof chainring defense in an innovative, lightweight package with zero efficiency loss make the SXg ideal for a wide range of uses. Whippersnapper™ technology provides lower retention without moving parts or friction. The most advanced chainguide on the market, the SXg is the go-to of the top Rampage stuntmen, World Cup downhill pilots, and superhuman enduro tacticians. - Whippersnapper™ lower guide. - Full-size, nylon HD upper guide with co-molding. - Integrated SX skid provides safeguard to the chainring and glides over rocks and obstacles. - Nylon and TPU co-molding in the Whippersnapper™ provides durable protection from external blows and mutes internal contact with the chain. - Swingset™ hardware. - All installation and adjustment operations are possible with just a single 4mm HEX wrench. - Available in 30-34t and 34-38t sizing. - Alloy guides compatible with chainlines 49mm and wider, carbon 50mm and wider. Boost 148 compatible. - ISCG-05 only. - 149g (34-38t Alloy ISCG-05)
Shimano XT Left Crank Arm - Spindle Interface Type: Hollowtech II
$10.00 - $12.00
Use these Wheels Manufacturing Crank Spindle Spacers to adjust chainline or bearing play in bottom brackets. - 24mm for Shimano Hollowtech II, FSA, Race Face EXI, SRAM GPX - 30mm for BB30, PF30, BB86, BB92 and other cranks with 30mm spindles - Machined engineering-grade Delrin - 10 spacers per bag
Wheels Manufacturing 2.5mm Black Aluminum Bottom Bracket Spacers are for adjusting chainline or bearing play in English (BSA) or Italian threaded bottom brackets.
Wheels Manufacturing Wave Washers help eliminate side play in cranks or pre-loaded angular contact bearings. Please refer to your crankset manufacturer's installation instructions for proper placement. - 24mm for Shimano Hollowtech II, FSA, Race Face EXI, SRAM GPX - 30mm for BB30, PF30, BB86, BB92 and other cranks with 30mm spindles - Uncompressed Thickness: 2.1mm - Compressed Thickness: 0.5mm - Spring Steel - 10 per bag
$382.45 $425.00 10% Off
Whether you're looking to take your training to the next level or you simply want a better way to measure energy expenditure, a power meter is your best bet. And the Power Cranks 105 Upgrade Kit are no exception. With our lightweight power sensors on a Shimano 105 crankarm, it's the perfect way to enter the power meter game. The development of Power Cranks began with our Human Performance Team looking at riders in realistic scenarios on the bike. Historically, power meters have been validated by two different methods—one is by measuring the produced torque by applying a static, linear load to a crankarm or chainring, while the second uses a power generating motor to pedal the bike. Well, cycling is neither static nor linear, and humans apply power much differently than a machine. So, we found that neither of these methods answers the 'real-world' accuracy question. To get the best test for accuracy, in all types of riding scenarios, we built our own cycling treadmill, the WinMill, to measure power output to a known truth. This new benchmark lets us evaluate accuracy under all riding conditions—seated versus standing, various power and cadence levels, different weights, and a myriad of gear. This data acquisition process is our gold-standard for testing power meters, and through our testing and external validation from the Locomotion Lab in Boulder, Colorado, Power Cranks have been proven to have the highest accuracy in real-world scenarios (+/- 1.5%). The Power Cranks are also easy to live with, with class-leading temperature compensation firmware and waterproof enclosures. Calibration is only required during seasonal-type fluctuations in temperature, and the included wrench makes battery swaps a breeze. - +/- 1.5% real-world accuracy tested on the WinMill and validated by the Locomotion Lab in Boulder, CO. - Works with ANT+ and Bluetooth devices. - Easy set-up and diagnostics with the Specialized Power app. (iOS and Android versions available). - Shimano 5800 generation 105 left-side power measurement. - Right crankarm and spider NOT included. - Available in 170-175mm crankarm lengths.
Trail riding can be tough on your gear. The ends of your carbon cranks can take a lot of abuse as the trail rushes underneath you and your bike. Protect your cranks from any damage with Race Face crank boots. Made from a durable Race Face proprietary plastic blend, leave no doubt and go with the originator in crank end protection. Wrap it up and protect the tips! Compatible with: - Race Face - Next SL Cinch (G3) - Sixc Cinch - Chester - Respond - Next/Next SL (24mm Spindle) - Sixc (24mm Spindle) - Most other popular carbon MTB cranks and assorted alloy DH cranks
Page 1 of 4 Next page